Valorization of Pennisetum setaceum: From Invasive Plant to Fiber Reinforcement of Injected Composites.

During the control campaigns of Pennisetum setaceum (invasive species widespread worldwide), the generated waste has accumulated in landfills. This study investigates its use to obtain P. setaceum fibers for their application as reinforcement of polymeric materials for injection molding, thus facilitating and promoting alternatives for the long-term sustainable management of P. setaceum. The extracted fibers were treated with alkaline, silane, acetic acid, and combined alkaline and silane treatments. Different composites with 20 and 40 wt% of fiber were extruded, and test samples were obtained by injection molding using recycled polyethylene as matrix. The composition of the fibers was determined by gravimetric methods, and contrasted with the analysis of the functional chemical groups using Fourier Transform Infrared Spectroscopy. Increases of up to 47% in the cellulose content of the treated fiber were observed. The thermal degradation was also evaluated using thermogravimetric analysis, which determined an increase in the degradation temperature, from 194 to 230 °C, after the combined alkaline-silane treatment. In order to analyze the differences in the composites, tensile, flexural, and impact properties were evaluated; in addition, differential scanning calorimetry was performed. Regarding the flexural behavior, it was possible to improve the flexural modulus up to 276% compared with that of the unreinforced polymer.

Environmental Hazards of Giant Reed (Arundo donax L.) in the Macaronesia Region and Its Characterisation as a Potential Source for the Production of Natural Fibre Composites.

This paper summarises the results obtained from the characterisation of giant reed (Arundo donax L.) plant and fibres. The research is part of a project developed in the Macaronesia region, of which the aim is to demonstrate the feasibility of using biomass from invasive plant species in the composites sector as a way of financing control campaigns and habitats conservation labours. An experimental procedure for the extraction of fibre bundles from this plant was developed, and the material obtained was characterised in terms of chemical composition, thermogravimetry and infrared spectra to evaluate its potential application in the production of polymeric composite materials as a strategy for the valorisation of residual biomass from this invasive species in Macaronesia. Thermoplastic matrix composites with fibre content up to 40 wt.% were produced and their mechanical properties under tensile, flexural and impact loading were determined. No references on the preparation of composite materials with polyolefin matrices and giant reed fibres have been found. Results obtained from mechanical tests show a good performance of the manufactured composites, with a significant increase in both flexural and tensile stiffness; the flexural modulus is almost tripled for PE-based composites and rises to 88% with respect to PP matrix. The ultimate flexural strength and the tensile and flexural yield strength are kept at acceptable values compared to neat polymer materials, although ultimate tensile strength and impact resistance are significantly affected when natural fibres are added.

Valorization of Invasive Plants from Macaronesia as Filler Materials in the Production of Natural Fiber Composites by Rotational Molding.

This paper compares the mechanical properties of different natural fiber composites produced by rotational molding as a way of waste valorization from campaigns to control invasive plant species in Macaronesia. Rotomolded parts produced with polymeric matrices (polyethylene) and filled with up to 20% by weight of cellulosic fibers obtained from Arundo donax L., Pennisetum setaceum, and Ricinus communis plants were characterized in terms of tensile, flexural, and impact strength. It was found that the sieving of natural fibers allowed for their introduction in higher loadings, from 10 (for un-sieved material) to 20%; fiber size greatly affected the mechanical properties of the final parts, although some combinations were proven not to reduce the mechanical properties of the neat resin. This study is a first approach to the valorization of residues obtained from periodic campaigns of the control of invasive species performed by public authorities, usually at the local level. It is important to highlight that the main objective of this research did not focus on economically profitable activity; instead, it was focused on the reduction of wastes to be disposed from ecosystem maintenance actions and the investment of potential income into preservation policies.

Three-dimensional printed polycaprolactone-microcrystalline cellulose scaffolds.

Microcrystalline cellulose (MCC) is proposed in this study as an additive in polycaprolactone (PCL) matrices to obtain three-dimensional (3D) printed scaffolds with improved mechanical and biological properties. Improving the mechanical behavior and the biological performance of polycaprolactone-based scaffolds allows to increase the potential of these structures for bone tissue engineering. Different groups of samples were evaluated in order to analyze the effect of the additive in the properties of the PCL matrix. The concentrations of MCC in the groups of samples were 0, 2, 5, and 10% (w/w). These combinations were subjected to a thermogravimetric analysis in order to evaluate the influence of the additive in the thermal properties of the composites. 3D printed scaffolds were manufactured with a commercial 3D printer based on fused deposition modelling. The operation conditions have been established in order to obtain scaffolds with a 0/90° pattern with pore sizes between 450 and 500 µm and porosity values between 50 and 60%. The mechanical properties of these structures were measured in the compression and flexural modes. The scaffolds containing 2 and 5% MCC have higher flexural and compression elastic modulus, although those containing 10% do not show this reinforcement effect. On the other hand, the proliferation of sheep bone marrow cells on the proposed scaffolds was evaluated over 8 days. The results show that the proliferation is significantly better (p < 0.05) on the group of samples containing 2% MCC. Therefore, these scaffolds (PCL:MCC 98:2) have suitable properties to be further evaluated for bone tissue engineering applications. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2018. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 107B: 521-528, 2019.